<![CDATA[Support]]>https://www.revoelectronics.com/blog/ Wed, 13 May 2026 10:59:43 +0000 Zend_Feed http://blogs.law.harvard.edu/tech/rss <![CDATA[Revolution TX(#57001) Revision History]]>https://www.revoelectronics.com/blog/tx-revision-history/ TX clone procedure(v3.03)
Tips:
For a safe TX clone, unplug the USB programmer(#57020) from the PC is recommended.
Check the TX battery voltage is over 3.8V.

Source TX:
Press Menu Button.
Scroll down then Select “7.CLONE TX” then press “STOP” button.
Select “SOURCE TX” then press “STOP” button.

Destination TX:
Press Menu Button.
Scroll down then Select “7.CLONE TX” then press “STOP” button.
Select “DESTINATION TX” then press “STOP” button.

Wait until both TX are powered Off.
The Destination TX is cloned by the Source TX and both have equal data memory.

Note:
Do not turn on the power both TX simultaneously after cloning TX. 
To avoid this problem, change the group ID number of each TX differently or set  "MULTI-TX"  to ON. 

 

]]> Fri, 01 Dec 2017 01:02:54 +0000 <![CDATA[Active Linear P&P Board #57079 - USA Train Wiring Photo]]>https://www.revoelectronics.com/blog/Active_Linear_Board/ <= Rev-01

]]> Mon, 14 Aug 2017 18:44:45 +0000 <![CDATA[Linear Base RX review]]>https://www.revoelectronics.com/blog/Linear-Base-RX-review/ By David bodnar:
Linear Super Base RX and USB Programmer Review

]]> Tue, 24 Jan 2017 19:46:35 +0000 <![CDATA[On Board #57002S #57102S #57012S #57202S Wiring]]>https://www.revoelectronics.com/blog/onboard-rx-wiring/ Caution Wiring!  ** Must Use Pure DC Power **
Basic Wiring Diagram
Extend Wiring Diagram
Battery Install Wiring Diagram
Smoke Board Wiring Diagram
#57012S micro RX Wiring Diagram
#57202S Dual Amp OnBoard RX Wiring Diagram
Brass Loco Signal Bypass

]]> Mon, 23 Jan 2017 16:22:02 +0000 <![CDATA[Device sound / firmware and PC software files]]>https://www.revoelectronics.com/blog/download-files-and-program/  

Onboard (#57002S ,#57102S, #57012S, #57202S) RX Sound Files

On Board Diesel1 
On Board Diesel2
On Board Diesel SD33 eco
On Board Diesel SD60
On Board Steam Generic sound
On Board Steam Midium Locomotive  #40

Note: The following sound files must be programmed after the patch file (OnBoard_Patch_R1) has been programmed.

OnBoard Patch R1
OnBoard Steam Small Locomotive 0-4-0 #6
OnBoard Steam Midium Locomotive  #90
OnBoard Diesel GP9 
 OnBoard_Diesel_Alco

 

#57001 TX firmware files

Revolution TX (Added clone function)  V3.03

Revolution TX   V3.02

 

#59001 DCC-TX  firmware files

Revolution DCC TX (Dead Rail , Cab(n)/RX(n) updated)   V1.14
Revolution DCC TX (Ack message updated)   V1.13
Revolution DCC TX (Optimized F: x0,x1,x2 access key)   V1.12
 

#59002 DCC-5A / #59105 Micro-DCC RX firmware files

 Revolution DCC RX (Soft Power-up updated)    V1.14
 Revolution DCC RX (Ack message updated)    V1.13
 

 

USB Programmer Windows PC Software

PC software v1.0
PC software v1.1   (added DCC TX/RX)

]]> Thu, 12 Jan 2017 17:00:59 +0000 <![CDATA[Crest(TM) products upgrade ]]>https://www.revoelectronics.com/blog/crest/ TX:
Silicone rubber keypad TX can be upgraded.
Do not upgrade the plastic keypad transmitter manufactured earlier.

On Board RX:
OnBoard Crest Patch file
Please program with the patch file(OnBoardCrestPatch1.zip)  first and then reprogram the desired file.
We are not responsible for any problems arising from the reprogram of Crest(TM) products.

]]> Fri, 30 Dec 2016 05:48:23 +0000 <![CDATA[Manual]]>https://www.revoelectronics.com/blog/revolution-manual1/ <= Revolution #57000
<= Revolution #57000 Quick Start Guide
<= Revolution DCC #59000
<= Revolution DCC #59000 v1.14 amended
<= Revolution Based RX
<= USB Programmer
<= Switch control board #57008B

]]> Tue, 01 Nov 2016 23:35:45 +0000